AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 293 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

293

5.7.5.6.5.

Examples

The following example shows a fax rate transmission speed of 9600 bps for faxes

sent using a dial peer:

voice service VoIP

fax rate 9600

5.7.5.7.

h323 call start

To force the H.323 Version 2 gateway to use Fast Connect or Slow Connect

procedures for all H.323 calls, use the

h323 call start

command in voice-service

configuration mode. To restore the default condition, use the

form of this

command.

h323 call start { fast | slow | preferred-slow }

no h323 call start

5.7.5.7.1.

Syntax

Keyword / Argument

Description

fast

Gateway uses H.323 Version 2 (Fast Connect)

procedures

slow

Gateway uses H.323 Version 1 (Slow Connect)

procedures.

preferred-slow

If you configure this option, at the time to make a

call, Gateway use slow start (normal start)
procedure. At the time to receive a call, Gateway

use slow start (normal start) or fast start procedure

depends on calling party’s configuration.

5.7.5.7.2.

Default Value

The default is

fast

5.7.5.7.3.

Command Mode

Voice-Service Configuration Mode

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды