AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 274 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

274

dial peers are selected, a hunting group will be made.

If a

huntstop

has been set already in a certain dial peer and if the outbound

call to that dial peer fails, a call will be terminated without hunting other dial

peers.

5.7.4.7.5.

Examples

The following example is to perform huntstop in VoIP peer 110.

dial-peer voice 110 VoIP

huntstop

5.7.4.8.

port

To associate a dial peer with a specific voice port, use the

port

dial-peer

configuration command. Use the

form of this command to cancel this

association.

port

slot/port

port

5.7.4.8.1.

Syntax

Keyword / Argument

Description

Slot

Slot number where the voice interface card is

installed. Valid entries are 1 or 0.

port

Port number for voice port number of voice

interface module. Valid entries are 1 to 7.

5.7.4.8.2.

Default Value

No port is configured.

5.7.4.8.3.

Command Mode

Dial-Peer Configuration Mode

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды