AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 39 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

Chapter 4

Gateway Configuration and Commands

This chapter describers how to configure the PassFinder AP2520 Gateway and

commands of the PassFinder AP2520 Gateway.

4.1.

Gateway Booting

The operator can use all commands of the AP2520 through the consol or Telnet

connection.

When power is supplied, the Gateway is booted as follows. :

The Gateway performs a self-test and checks basic operations of the CPU,

the memory and interfaces.

The boot loader is executed, and the boot loader seeks for proper

Gateway software image files. In the default configuration, the boot

loader loads Gateway software in the flash memory.

If the boot loader does not find any proper Gateway software image file

from the flash memory, the boot loader stands by in the boot mode until it

receives proper Gateway software from the system. (At this time, the

boot loader can download Gateway software through TFTP or FTP

protocol.)

When Gateway software is loaded, Gateway starts to operate according

to configuration information saved in the Gateway. However, if there is no

configuration information, the Gateway operates according to the default

values, and in this case, the operator shall set up related items for normal

operation of the network.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды