AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 292 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

292

5.7.5.6.1.

Syntax

Keyword / Argument

Description

2400

Specifies a fax transmission speed of 2400 bps.

4800

Specifies a fax transmission speed of 4800 bps.

7200

Specifies a fax transmission speed of 7200 bps.

9600

Specifies a fax transmission speed of 9600 bps.

12000

Specifies a fax transmission speed of 12,000 bits per

second (bps).

14400

Specifies a fax transmission speed of 14,400 bps.

disable

Disables Fax Relay transmission capability.

5.7.5.6.2.

Default Value

14400 bps

5.7.5.6.3.

Command Mode

Voice-Service Configuration Mode

5.7.5.6.4.

Usage Guideline

Use the

fax rate

command to specify the fax transmission rate to all dial peers.

The values for this command apply only to the fax transmission speed and do

not affect the quality of the fax itself. The higher transmission speed values

(14,400 bps) provide a faster transmission speed but monopolize a significantly

large portion of the available bandwidth. The lower transmission speed values

(2400 bps) provide a slower transmission speed and use a relatively smaller

portion of the available bandwidth.

This command is meaningful only under T.38 Fax Relay. If the fax rate is

disabled, T.38 fax relay does not operate. The fax relay made by the bypass

mode performs no operation in the gateway (as it does nothing for the fax

communication in the PSTN network) setting the rate does not mean anything.

Although T.38 is set as 14400 bps by this command, if two fax machines on both

sides operate at 9600, actual fax rate will be 9600 bps.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды