AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 212 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

212

5.6.2.

Configuring H323 Call Start Mode

In H.323 version2, logical channel negotiation procedures made by the fast

start mode upon the start of the H.323 call is explained.

In the voice service VoIP setup mode, users can select the fast start

procedures by using “

h323 call start

” command in the AP2520 Gateway.

The fast start mode is the default, and H245 tunneling and the fast start is

disabled when the slow start is set.

To find out the capability (T.38 fax, DTMF relay capability, etc.) of the other side

in the fast start mode, users can perform H.245 procedures.

Step Command

Description

Router# configure

Enters into the global configuration

mode.

Router(config)# voice service VoIP

Enters into the voice service VoIP

setup mode.

Router(vservice-VoIP)# h323 call start
{fast | slow}

Sets the fast mode or the slow start

mode.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды