AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 273 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

273

forward-digit from 99

If “

forward-digit last

” is added as below, only last four digits “6789” will be

forwarded.

forward-digit last 4

In the following example, no digit is forwarded.

forward-digit last 0

In the following digit, all digits “100123456789” are forwarded.

forward-digit last 99

5.7.4.7.

huntstop

To stop dial peer hunting in the hunting group, use “

huntstop

” command in the

dial-peer setup mode. To use default setting, use “

” command before

“

huntstop

” command.

huntstop

no huntstop

5.7.4.7.1.

Syntax

This command has no arguments or keywords.

5.7.4.7.2.

Default Value

Hunting can be made in the default state.

5.7.4.7.3.

Command Mode

Dial-Peer Configuration Mode

5.7.4.7.4.

Usage Guideline

If an outbound dial peer is selected for an inbound call and if more than one

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды