AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 288 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

288

5.7.5.2.4.

Usage Guideline

The gateway at opposite ends of the WAN may have to negotiate the codec

selection for the network dial peers. The codec preference command specifies

the order of preference for selecting a negotiated codec for the connection.

5.7.5.2.5.

Examples

The following example creates codec preference list 99 and applies it to dial
peer 1919:

voice class codec 99

codec preference 1 g711alaw

codec preference 2 g711ulaw

codec preference 3 g7231r63

codec preference 4 g729

end

dial-peer voice 1919 VoIP

voice-class codec 99

5.7.5.3.

counter

To set VoIP-related counter parameter value, use “

counter

” command in the

voice service setup mode. To convert this setup into the default state, use

“

” command before this command.

counter { cras }

value

no counter { cras }

5.7.5.3.1.

Syntax

Keyword / Argument

Description

cras

value

RAS message retransmission counter with the
gatekeeper.

The value ranges from 1 to 5, and the default is 3.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды