AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 51 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

4.2.3.3.

Commands of the Interface Configuration Mode 2 (IP

Configuration Mode)

The user can use IP related commands in the selected interface.

The prompt is indicated as router(config-ether0.0)#.

Command

Description

access-group

applies the access-list that has been set in the global

configuration environment to the interface.

accounting

Apply IP Account List to the selected interface.

address

Sets or changes the IP address of the Interface.

dhcp-group

applies the DHCP-list that has been set in the global

configuration environment to the interface.

exit

Returns to the previous (configuration) menu.

end

Returns to the initial (Exec) mode.

nat-group

applies the NAT-list that has been set in the global

configuration environment to the interface.

Cancels the environment parameters that have been set in

the configuration mode or returns them to the default

values.

proxy-arp

Enables IP proxy ARP for the corresponding interface.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды