AddPac PassFinder AP2520 Скачать руководство пользователя

Страница: 272 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

272

are forwarded.

5.7.4.6.2.

Default Value

In the default, if the called party number matches with the destination pattern

of the outbound POTS peer, only digits that are not matched will be forwarded.

5.7.4.6.3.

Command Mode

Dial-Peer Configuration Mode (POTS peer)

5.7.4.6.4.

Usage Guideline

This command is a dial-peer setup mode command and applied only to the

POTS peer.

This command is used to define number of digits when relaying last digits of the

called party number of an inbound call as the called party number of the

outbound call. The default is no forward-digit, and in the default status, number

forwarding is made.

5.7.4.6.5.

Examples

If POTS peer 10 is decided for the outbound, call and if the called party

number of the inbound call is 100123456789, number 123456789 will be

forwarded as set in the default. This is because “

forward-digit

” has not been

set.

dial-peer voice 10 pots

destinarion-pattern 100...

If “

forward-digit from

” is added to the above setting, only “456789” (from the 7

digit to the last digit) will be forwarded.

forward-digit from 7

In the following example, all digits (100123456789) will be forwarded.

forward-digit from 1

In the following example, no digit will be forwarded.

Содержание PassFinder AP2520

















































































































































































































































































































































































Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды

AddPac PassFinder AP2520, Руководство пользователя

Результаты поиска

Содержание PassFinder AP2520

Отзывы:

Похожие инструкции для PassFinder AP2520

Бренды по названию

Популярные бренды