Volvo 2008 C30 Service And Repair Manual Download | Manualshive

Page: 746 / 943

background image

Guide in the sun roof in relation to the guide holes.

Tighten the screws in numerical order as illustrated. Tighten. See:

TIGHTENING TORQUE

.

INSTALLING SUN ROOF COMPONENTS

Install:



the electric motor / control module. See:

THE ELECTRIC MOTOR / SUN ROOF MODULE (SRM).



the connector.

Connect the 4 drain hoses.

Install:



the sun visor / inner sun roof. See:

SUN VISOR/INNER COVER SUN ROOF



the wind deflector. See:

WIND DEFLECTOR SUNROOF



the sun roof glass. See:

GLASS SUN ROOF

.

FINISHING

ADJUSTING AND CHECKING THE SUN ROOF

Adjust the sun roof glass. See:

SUN ROOF

.

Check for leakage. See:

LEAK TESTING THE SUN ROOF

.

Install the headlining. See:

HEADLINING WITH SUN ROOF

.

NEW CALIBRATION OF ELECTRIC MOTOR / SUN ROOF MODULE (SRM)

When installing a

new

electric motor / control module, perform new calibration. See:

NEW CALIBRATION

OF ELECTRIC MOTOR / SUN ROOF MODULE (SRM)

.

RECALIBRATION OF ELECTRIC MOTOR / SUN ROOF MODULE (SRM)

When installing a

previously used

electric motor / control module, perform recalibration. See:

RECALIBRATION OF THE ELECTRIC MOTOR/SUN ROOF MODULE (SRM)

.

SUN VISOR/INNER COVER SUN ROOF

REMOVAL

NOTE:

The illustrations in this service information are used for different model years
and/or models. Some variation may occur. However, the essential information in
the illustrations is always correct.

2012 Volvo C30 T-5

ACCESSORIES AND BODY, CAB Doors And Lids - Removal, replacement and installation

«
...
744
745
746
747
748
...
»

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 C30

Brand: Kathrein Pages: 7

Brand: Whispbar Pages: 15

Brand: Volvo Pages: 42

Brand: GReddy Pages: 12

Brand: Classic AutoAir Pages: 44

Brand: Acura Pages: 4

Brand: Ford Pages: 264

Brand: Mercedes-Benz Pages: 66

FUEL TANK GAUGE

Brand: VDO Pages: 10

Brand: Blue Bird Pages: 111

Brand: GMC Pages: 24

Brand: Kia Pages: 17

Brand: Yutrax Pages: 8

Brand: AEM Pages: 5

DT-Mobil Easy 200 L

Brand: CEMO Pages: 80

Brand: Split Phantom Pages: 20

Brand: Camoplast Pages: 14

Brand: BOSSCO Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands