Volvo 2008 C30 Service And Repair Manual Download Page 473

Page: 473 / 943

FINISHING

CHECKING THE FUNCTION AND LEAK TRACING

Tighten the drain nipple on the radiator.

Fill with coolant and warm up the engine until the thermostat opens. Top up if necessary.

Check that the pipe coupling does not leak.

Vacuum pump the air conditioning (A/C) system. See:

VACUUM PUMPING

Fill the air conditioning (A/C) system with refrigerant. See:

REFRIGERANT, FILLING

Leak trace the air conditioning (A/C) system. See:

LEAK DETECTION, TRACER AGENT

LEAK

TRACING, ELECTRONIC LEAK TRACER (2008-2009)

LEAK TRACING, ELECTRONIC LEAK

TRACER (2007, 2010-11)

Fig. 99: Identifying Shield And Clips

Courtesy of VOLVO CARS CORPORATION

Install:

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands