Volvo 2008 C30 Service And Repair Manual Download

Page: 354 / 943

5. Climate control unit

6. Air quality sensor (AQS).

LOCATION OF THE CLIMATE CONTROL UNIT COMPONENTS

Fig. 2: Identifying Climate Control Unit Components

Courtesy of VOLVO CARS CORPORATION

1. Heat exchanger

2. Evaporator

3. Fan motor

4. Damper motor module (DMM) air distribution

5. Damper motor module (DMM) temperature, right-hand

6. Damper motor module (DMM) temperature, left-hand

7. Damper motor module (DMM) recirculation

8. Damper motor module (DMM) defroster

9. Evaporator temperature sensor

10. Air cleaner (ACL) passenger compartment.

LOCATING COMPONENTS IN THE ENGINE COMPARTMENT

2012 Volvo C30 T-5

HVAC Climate Units - Component Location

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands