Volvo 2008 C30 Service And Repair Manual Download Page 200

Page: 200 / 943

Fig. 158: Prying Off Hooks From Mountings In Bumper Cover

Courtesy of VOLVO CARS CORPORATION



Carefully pry off the hooks from the mountings in the bumper cover and remove the existing Skid plate, it
will not be reused.

APPLIES TO CARS WITH PARKING ASSISTANCE

Fig. 159: Identifying Protective Film

Courtesy of VOLVO CARS CORPORATION



Remove the protective film from one side of the double-backed tape.

NOTE:

Take extra care when working with the bumper cover and Skid plate.

2012 Volvo C30 T-5

ACCESSORIES AND EQUIPMENT Bumpers And Mudflaps - Installation Instructions, Accessories

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands