Volvo 2008 C30 Service And Repair Manual Download

Page: 380 / 943

Fig. 18: Identifying Air Distribution Unit

Courtesy of VOLVO CARS CORPORATION

Remove the dashboard. See:

DASHBOARD

Turn the dashboard upside down.

Remove the 3 screws and the 2 tie straps. Lift up the cable duct.

Disconnect the connector for the sun sensor / alarm LED.

INSTALLING THE AIR DISTRIBUTION UNIT IN THE DASHBOARD

Install:



the air distribution unit to the air ducts for the outer vents



the cable duct using the 3 screws and 2 tie straps



the connector for the sun sensor / alarm LED



the dashboard. See:

DASHBOARD

AIR DUCT OUTER VENT, REPLACING

REMOVING AIR DUCT OUTER VENT

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands