Volvo 2008 C30 Service And Repair Manual Download Page 623 | Manualshive

Page: 623 / 943

background image

PREPARATORY WORK

TRANSFERRING COMPONENTS

Fig. 27: Applying Thread Lock To Bolt Threads

Courtesy of VOLVO CARS CORPORATION

Move the ball catch to the new gear box.

Apply the thread lock 1161056 to the threads.

Tighten to 32 Nm.

When replacing the transmission, the transmission cable bracket must be transferred to the new transmission.

INSTALLATION

CLEANING AND LUBRICATING THE INPUT SHAFT

The input shaft must be lubricated before a manual transmission is installed. See

INPUT SHAFT,

CLEANING

.

CHECKING BEFORE INSTALLING

Check that the transmission and engine mating surfaces are absolutely clean.

Also check that the guide sleeves towards the engine are in position and are free of faults. Lubricate the holes in
the transmission (for the guide pins). Use a little grease.

is always correct.

NOTE:

For tightening torques, See TIGHTENING TORQUE .

2012 Volvo C30 T-5

TRANSMISSION Clutch - Removal, replacement and installation

«
...
621
622
623
624
625
...
»

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 C30

Brand: Harbor Freight Tools Pages: 4

Brand: Jeep Pages: 603

Brand: Jeep Pages: 80

Brand: Uebler Pages: 18

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Tachosys Pages: 28

Brand: Hyundai Pages: 19

Brand: Audiovox Pages: 3

Brand: Victory 4x4 Pages: 9

Brand: Whispbar Pages: 15

Brand: Brigade Pages: 12

Brand: Curt Group Pages: 2

Brand: Buick Pages: 20

Brand: Yakima Pages: 10

QuadraTop Adventure Top 1113.00 Series

Brand: Quadratec Pages: 20

Brand: Canyon Pages: 2

Brand: MeiTrack Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands