Volvo 2008 C30 Service And Repair Manual Download

Page: 103 / 943

BRAKES

Hydraulic-Vacuum-Hydraulic Brakes - Installation Instructions, Accessories

METAL PEDALS

Fig. 1: Removing Original Covers (Manual Transmissions)

Courtesy of VOLVO CARS CORPORATION

Graphic above applies to cars with manual transmissions. Graphic below applies to cars with automatic
transmissions



Remove the rubber covers from the pedals by grasping the upper edge and pulling backwards.



Clean, if necessary, all pedal surfaces where the new rubber covers will be positioned.

Fig. 2: Removing Original Cover (Automatic Transmissions)

2012 Volvo C30 T-5

BRAKES Hydraulic-Vacuum-Hydraulic Brakes - Installation Instructions, Accessories

2012 Volvo C30 T-5

BRAKES Hydraulic-Vacuum-Hydraulic Brakes - Installation Instructions, Accessories

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands