Volvo 2008 C30 Service And Repair Manual Download Page 629

Page: 629 / 943

Fig. 34: Identifying Back-Up Lamp Switch Connector And Transmission Cables To Bracket And Levers
Courtesy of VOLVO CARS CORPORATION

Install:



the connector for the back-up lamp switch



the transmission cables to the bracket and levers. Adjust the transmission cable. See

TRANSMISSION

CABLE, ADJUSTING

INSTALLING THE AIR CLEANER (ACL) MODULE

Fig. 35: Identifying Air Cleaner (ACL) Module And Rubber Hose For Throttle Housing

Courtesy of VOLVO CARS CORPORATION

Install the air cleaner (ACL) module. See.

INSTALLING COMPONENTS

NOTE:

Ensure that the cable and sleeve do not crack or break.

2012 Volvo C30 T-5

TRANSMISSION Clutch - Removal, replacement and installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands