Volvo 2008 C30 Service And Repair Manual Download Page 465

Page: 465 / 943

DRAINING COOLANT AND REMOVING THE COVER

Fig. 91: Identifying Shield And Clips

Courtesy of VOLVO CARS CORPORATION

Remove the expansion tank cap.

Raise the vehicle.

Remove the shield under the vehicle. It is secured with 7 clips. See the illustration.

Install a hose on the nipple at the radiator.

Feed the hose down to a container.

Open the nipple. Drain off the engine coolant.

Disconnect the quick-release connectors for the cooler hoses at the cowl panel in the engine compartment.

REMOVING COMPONENTS

Remove:

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands