Volvo 2008 C30 Service And Repair Manual Download Page 437

Page: 437 / 943

Install the drive belts. See:

ACCESSORY DRIVE BELT TENSIONER

FINISHING

CHECKING THE FUNCTION AND LEAK TRACING

Vacuum pump the air conditioning (A/C) system. See:

VACUUM PUMPING

Fill the AC-system with refrigerant acc. to:

REFRIGERANT, FILLING

Leak trace the air conditioning (A/C) system. See:

LEAK DETECTION, TRACER AGENT

LEAK

TRACING, ELECTRONIC LEAK TRACER (2007, 2010-11)

LEAK TRACING, ELECTRONIC

LEAK TRACER (2008-2009)

CHECKING THE PERFORMANCE

Fig. 67: Identifying Shield And Clips

Courtesy of VOLVO CARS CORPORATION

Install the shield under the vehicle using the 7 clips.

Carry out a performance test on the climate control unit. See:

CLIMATE CONTROL SYSTEM, CHECK

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands