Volvo 2008 C30 Service And Repair Manual Download

Page: 591 / 943

Fig. 199: Identifying Water Pump

Courtesy of VOLVO CARS CORPORATION

The water pump for the engine coolant heater has a rubber-mounted mounting. The lower section is hooked
onto the mounting bracket on the vehicle.

Install:



the hoses using new hose clamps according to any markings. Remove the hose clips



the water pump and mounting, 1 x M6. Tighten

HINT: Hook the lower reverse of the rubber mounting in the mounting. This facilitates locating the
thread hole and correct mounting.



the connector.

Close the drain nipple. Remove the hose.

Fill with coolant. Run the engine until the thermostat opens. Top up if necessary.

FINISHING

ADJUSTING AND CHECKING

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands