Volvo 2008 C30 Service And Repair Manual Download

Page: 566 / 943

Fig. 179: Identifying Intake Hose, Exhaust System, Fuel Pipe And Mounting Screw

Courtesy of VOLVO CARS CORPORATION

Disconnect the intake hose (1).

Disconnect the exhaust system (2) but do not remove it. See

FUEL FIRED BOOSTER HEATER EXHAUST

PIPE (B5244S4)

Remove:



the fuel pipe (3) from the clip mounting



the mounting screw (4). Angle the engine coolant heater out slightly.

Place paper around the upper fuel connection on the engine coolant heater.

Disconnect the fuel hose.

HINT: Use: see 9512619 to release the clamps.

Lift up and remove the fuel line.

INSTALLING THE FRONT FUEL LINE

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands