Volvo 2008 C30 Service And Repair Manual Download Page 470

Page: 470 / 943

Fig. 96: Identifying Evaporator Screws

Courtesy of VOLVO CARS CORPORATION

Remove the 3 screws. Remove the cover.

Pull out the evaporator. Pull alternately at the top and bottom edges. It may be hard to remove.

INSTALLATION

INSTALLING THE EVAPORATOR

Install a

new

seal, using the removed evaporator as a template.

NOTE:

Note how the seal is located on the evaporator.

NOTE:

For tightening torques, see: TIGHTENING TORQUE .

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands