Volvo 2008 C30 Service And Repair Manual Download Page 577 | Manualshive

Page: 577 / 943

background image

TESTING THE ENGINE COOLANT HEATER

Carry out a performance test of the engine coolant heater. See:

FUEL-POWERED PREHEATER,

CHECKING

.

FUEL PUMP, FUEL-DRIVEN AUXILIARY HEATER (B5244S4)

PREPARATORY WORK

IMPORTANT INFORMATION

Fig. 187: Identifying Fuel Pump (FP)

Courtesy of VOLVO CARS CORPORATION

NOTE:

The illustrations in this service information are used for different model years
and/or models. Some variation may occur. However, the essential information in
the illustrations is always correct.

WARNING:

Use protective gloves and protective goggles during all operations due to
the risk of fuel spills.

NOTE:

There must be no dirt present when handling the fuel lines' connections.

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

«
...
575
576
577
578
579
...
»

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 C30

Brand: RAM Pages: 20

Brand: Vauxhall Pages: 2

Brand: Porsche Pages: 195

Brand: Victory 4x4 Pages: 13

ANDROID INTERFACE

Brand: GMC Pages: 18

Brand: Prorack Pages: 15

Brand: Haibang Pages: 6

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Brand: Gator Pages: 2

PRIME DESIGN VRR-NV200

Brand: Safe Fleet Pages: 12

Brand: TATA Motors Pages: 136

Brand: Mercedes-Benz Pages: 358

Brand: T-Mobile Pages: 2

Brand: Caltrend Pages: 3

Brand: Draw tite Pages: 4

Brand: Curtis Pages: 6

IT FITS RBO1018

Brand: RBO Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands