Volvo 2008 C30 Service And Repair Manual Download

Page: 751 / 943

Fig. 43: Locating Electric Motor / Control Module Screws

Courtesy of VOLVO CARS CORPORATION

Remove the 3 screws.

Carefully lower the electric motor / control module.

INSTALLATION

INSTALLING ELECTRIC MOTOR / SUN ROOF MODULE (SRM)

Install:



the electric motor / control module



the 3 screws. Tighten.

Tighten the 3 screws for the interior lighting frame.

Install:



the connector



the front courtesy lighting. See:

LIGHTING, INTERNAL FRONT

2012 Volvo C30 T-5

ACCESSORIES AND BODY, CAB Doors And Lids - Removal, replacement and installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands