Volvo 2008 C30 Service And Repair Manual Download Page 156 | Manualshive

Page: 156 / 943

background image

Fig. 71: View Of Left Front And The Center Mounting Hole

Courtesy of VOLVO CARS CORPORATION



Now take a loose drill bit with the same diameter as the holes in the front mounting holes and rotate to
create a marking on the longitudinal markings.



Remove the engine splash guard after marking.

Fig. 72: View Of Both Right-Hand Front Mounting Holes

Courtesy of VOLVO CARS CORPORATION



Previous graphic shows the left front and the center mounting hole.



Graphic above shows both right-hand front mounting holes.

NOTE:

take care when marking the two front hole. Drill the large holes on the
narrow panel edge.

2012 Volvo C30 T-5

ACCESSORIES AND EQUIPMENT Bumpers And Mudflaps - Installation Instructions, Accessories

«
...
154
155
156
157
158
...
»

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 C30

Brand: Toyota Pages: 529

witty park XEV6 Series

Brand: hager Pages: 9

Brand: Laser Pages: 8

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Brand: iOttie Pages: 58

Electra 225 1965

Brand: Buick Pages: 914

Brand: Draw tite Pages: 4

Brand: EFILive Pages: 25

Brand: TEINHOF Pages: 2

Brand: TrailFX Pages: 2

Brand: Mercedes-Benz Pages: 10

Brand: Mitsubishi Pages: 362

Brand: Connects2 Pages: 2

transit connect 2012

Brand: Ford Pages: 299

Brand: AUTOTECH Pages: 4

MAGIC WATCH MWE-850-4XXL

Brand: Waeco Pages: 228

Brand: Macally Pages: 10

Brand: FALCON RIDGE Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands