Volvo 2008 C30 Service And Repair Manual Download Page 504 | Manualshive

Page: 504 / 943

background image

Perform a performance test of the engine's preheater. See:

FUEL-POWERED PREHEATER, CHECKING

COOLANT PIPE FUEL-POWERED PREHEATER (B5254T3, B5254T7)

PREPARATORY WORK

REPLACING PIPE COUPLINGS

Remove:



the engine coolant heater. See:

FUEL FIRED BOOSTER HEATER (B5254T3, B5254T7)



the engine coolant hose(s) from the pipe coupling(s) on the engine coolant heater.

HINT: Mark out the internal location of the engine coolant hoses and the angle of the pipe couplings in
relation to the cover.

REMOVAL

REMOVING THE COVER OVER THE HEAT EXCHANGER

NOTE:

The illustrations in this service information are used for different model years
and/or models. Some variation may occur. However, the essential information in
the illustrations is always correct.

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

«
...
502
503
504
505
506
...
»

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 C30

Brand: Warrior Products Pages: 3

Brand: Vauxhall Pages: 323

Brand: Inbay Pages: 20

Brand: P-Invent Pages: 4

Brand: Brodit Pages: 2

Brand: Quadratec Pages: 14

Brand: Acura Pages: 19

Brand: Ford Pages: 325

Brand: Porsche Pages: 146

2004 JR41 Stratus Sedan

Brand: Dodge Pages: 273

Brand: Saab Pages: 9

2013 Cadillac CTS-V

Brand: Cadillac Pages: 6

Brand: J Communications Pages: 10

Brand: FORM FIT Pages: 4

Traffic Advisor TA1252L

Brand: Whelen Engineering Company Pages: 4

Brand: Cadillac Pages: 9

Brand: Jegs Pages: 2

PRIUS 50 2020 Series

Brand: Toyota Pages: 551

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands