Volvo 2008 C30 Service And Repair Manual Download

Page: 685 / 943

Fig. 24: Identifying Relay/Fuse Holder's Screw(s)

Courtesy of VOLVO CARS CORPORATION

Remove the relay/fuse holder's screws, 2 pcs. Lift the relay/fuse holder straight up at the trailing edge. Remove
the lower casing.

Fig. 25: Identifying Position Of Relays

Courtesy of VOLVO CARS CORPORATION

For the location of the relays and fuses, see



decals at each respective relay and fuse box in the vehicle.



Pocket Data Booklet

Remove the front secondary catch, lift with a screwdriver.

NOTE:

Note the position of the relays. Remove relays and fuses from the relay/fuse
holder as needed.

2012 Volvo C30 T-5

ELECTRICAL Cables And Fuses - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands