Volvo 2008 C30 Service And Repair Manual Download Page 484

Page: 484 / 943



the pipe coupling by the compressor, 1 M8. Make sure the O-rings are securely located. Tighten the screw



the charge air pipe upper and lower connectors.

Carry out finishing work. See:

FINISHING

PIPE/HOSE BETWEEN COMPRESSOR AND RECEIVER (SUCTION SIDE), REPLACING

REMOVING THE PIPE/HOSE BETWEEN THE COMPRESSOR AND THE RECEIVER

Fig. 107: Identifying Lower/Front Pipe/Hose Connector

Courtesy of VOLVO CARS CORPORATION

Remove the lower/front pipe/hose connector (2) on the compressor.

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands