Volvo 2008 C30 Service And Repair Manual Download Page 763

Page: 763 / 943

Fig. 61: Identifying Level Adjustment

Courtesy of VOLVO CARS CORPORATION

The front part must be positioned above the part behind it (see illustration), partly to overlap in case of a
collision, partly to reduce wind noise.

Measurement M1 = 0.5 mm.

MEASUREMENTS, ENGINE HOOD

2012 Volvo C30 T-5

ACCESSORIES AND BODY, CAB Doors And Lids - Removal, replacement and installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands