Volvo 2008 C30 Service And Repair Manual Download Page 386

Page: 386 / 943

Fig. 23: Identifying Removal Of Sill Trim Panel From Rear Side Door

Courtesy of VOLVO CARS CORPORATION

Pull the front edge straight up.

Ease out the rear mount against the C-post panel.

INSTALLING THE SILL TRIM PANEL FOR THE REAR SIDE DOOR

Secure the rear mount against the C-post panel.

Press the sill trim panel into place.

SILL TRIM PANEL TRUNK LID, REPLACING

REMOVING THE SILL TRIM PANEL TRUNK LID

CAUTION: Ensure that the sill trim panel goes into the groove at the B-pillar panel.

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands