Volvo 2008 C30 Service And Repair Manual Download

Page: 479 / 943

Fig. 103: Identifying Needle Valve/Service Valve

Courtesy of VOLVO CARS CORPORATION

Remove the needle valve in the service valve. Use: see

9511204

INSTALLATION

INSTALLING THE NEEDLE VALVE / SERVICE VALVE

Install the needle valve. Use: see

9511204

Use: see

9811994

and tighten, see:

TIGHTENING TORQUE

FINISHING

CHECKING THE FUNCTION AND LEAK TRACING

Vacuum pump the air conditioning (A/C) system. See:

VACUUM PUMPING

Fill the air conditioning (A/C) system with refrigerant. See:

REFRIGERANT, FILLING

NOTE:

Use only your finger and thumb when tightening the needle valve to avoid
damage to the valve seal.

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands