Volvo 2008 C30 Service And Repair Manual Download Page 172

Page: 172 / 943

Fig. 102: Hooking Sill Decore Onto Cradle

Courtesy of VOLVO CARS CORPORATION



Hook the sill decor onto the cradle. Align the holes in the panel with the hooks in the cradles.



Press the decor strip into position securely so that all hooks engage.

Fig. 103: Drilling Out Hole

Courtesy of VOLVO CARS CORPORATION



Press the sill decor opposite the mounting lug for the center hole against the underneath of the door sill
panel. Drill out the hole using a

6 mm (15/64")

drill bit. Remove the drill shavings.

2012 Volvo C30 T-5

ACCESSORIES AND EQUIPMENT Bumpers And Mudflaps - Installation Instructions, Accessories

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands