Volvo 2008 C30 Service And Repair Manual Download Page 483

Page: 483 / 943

Fig. 106: Identifying Rear Connector

Courtesy of VOLVO CARS CORPORATION

Lower the vehicle.

Remove the upper charge air cooler (CAC) hose.

Remove the dip stick.

Disconnect the rear connector (1) to the condenser, to the left of the right-hand headlamp. See the illustration.

Route the pipe/hose down to the compressor under the vehicle.

INSTALLING THE PIPE/HOSE BETWEEN THE COMPRESSOR AND THE CONDENSER

Place the pipe/hose for the compressor in position by the upper connector to the condenser.

Install:



the pipe coupling, 1 M8. Ensure that the O-rings are securely located between the condenser and the
pipe/hose. Tighten the screw

NOTE:

For tightening torques, see: TIGHTENING TORQUE .

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands