Volvo 2008 C30 Service And Repair Manual Download

Page: 545 / 943

Fig. 160: Identifying Combustion Preheater Module (CPM) Screws

Courtesy of VOLVO CARS CORPORATION

Slacken off the 4 screws. See the illustration.

Carefully pull the combustion preheater module (CPM) straight out to access the connector.

Position a small screwdriver between the control module connector and its 2 catches. Turn the screwdriver
carefully to release the catches.

Pull off the control module.

INSTALLATION

INSTALLING THE COMBUSTION PREHEATER MODULE (CPM)

Install the switch so that it is properly secured.

Position the control module. Ensure that the control module housing goes correctly into the grooves at the top
edge.

Tighten the 4 screws crosswise.

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands