Volvo 2008 C30 Service And Repair Manual Download Page 488

Page: 488 / 943

Fig. 110: Identifying Coolant Reservoir, Power Steering Fluid Reservoir And Hoses

Courtesy of VOLVO CARS CORPORATION

Remove:



the coolant reservoir (1) but leave the hoses in place. Place the reservoir on the valve cover



the power steering fluid reservoir and hoses (2) from its mounting by pulling it upwards at an angle.

Remove:



the ground strip (3) from the connection at the right-hand suspension turret



the 2 switches (4) for the air conditioning (A/C) system pressure sensor from the air conditioning (A/C)
pipes / hoses



the front bumper cover. See:

COVER BUMPER FRONT (2010, 2011 EARLY)

COVER BUMPER

FRONT (2011 LATE - 2012)

REMOVING THE PIPE/HOSE BETWEEN THE EVAPORATOR AND THE RECEIVER

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands