Volvo 2008 C30 Service And Repair Manual Download Page 236

Page: 236 / 943

Fig. 230: Cleaning Areas Underneath Spoiler

Courtesy of VOLVO CARS CORPORATION



Take the front spoiler from the kit.



Clean the marked areas underneath the spoiler where the anti-chafing protector is to be located. Use
isopropanol. Wipe dry.

Fig. 231: Identifying Protective Tape

Courtesy of VOLVO CARS CORPORATION



Remove the protective tape from the anti-chafing protector.

NOTE:

The unpainted spoiler must be painted first.

2012 Volvo C30 T-5

ACCESSORIES AND EQUIPMENT Bumpers And Mudflaps - Installation Instructions, Accessories

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands