Volvo 2008 C30 Service And Repair Manual Download Page 551

Page: 551 / 943

Fig. 166: Identifying EVAP Canister Pipe And Upper Charge Air Pipe

Courtesy of VOLVO CARS CORPORATION

Remove:



the EVAP canister hose (1) from the intake manifold



the intake manifold (2) between the air cleaner (ACL) and the turbocharger (TC).

Remove:



the hose clamps at the mass air flow (MAF) sensor



the hose clamps at the turbocharger (TC)



the screws for the intake manifold in the cylinder head.

REMOVAL

REMOVING THE EXHAUST PIPE FOR THE ENGINE COOLANT HEATER

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands