Volvo 2008 C30 Service And Repair Manual Download Page 547

Page: 547 / 943

Pull off the intake hose that covers the upper mounting for the exhaust system.

Move the intake hose to one side.

Disconnect the upper mounting (as illustrated). Remove the screw.

Fig. 162: Identifying Shield And Clips

Courtesy of VOLVO CARS CORPORATION

Raise the vehicle.

Remove:



the right-hand front wheel



the shield under the vehicle. It is secured with 7 clips.

Disconnect the water pump. See:

WATER PUMP, FUEL-DRIVEN AUXILIARY HEATER (2007-2009)

Leave the water pump hanging from its hoses.

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands