Volvo 2008 C30 Service And Repair Manual Download Page 493

Page: 493 / 943

Fig. 115: Identifying Rear Connector

Courtesy of VOLVO CARS CORPORATION

Unscrew the cover from the service valve.

Remove:



the service valve using an extended 24 mm sleeve



the screw (2) at the condenser connection.

INSTALLING THE PIPE / HOSE BETWEEN THE CONDENSER AND THE EXPANSION VALVE

Install the cap nut for the expansion valve.

Install:



the M8 screw on the condenser connection



the service valve. Tighten. See:

TIGHTENING TORQUE



the service valve cover.

NOTE:

For tightening torques, see: TIGHTENING TORQUE .

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands