Volvo 2008 C30 Service And Repair Manual Download Page 246

Page: 246 / 943

Fig. 250: Identifying Fender Liner And Clips

Courtesy of VOLVO CARS CORPORATION



Reinstall the fender liner.



Get new clips from the kit and press in to the fender liner.



Press in the fender liner with clips in the fender edge's clips. Make sure that the clips really snap into
place.

Fig. 251: Identifying Panel On Fender Edge

Courtesy of VOLVO CARS CORPORATION



Press in the new panel on the fender edge. Make sure all catches engage.

2012 Volvo C30 T-5

ACCESSORIES AND EQUIPMENT Bumpers And Mudflaps - Installation Instructions, Accessories

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands