Volvo 2008 C30 Service And Repair Manual Download Page 383

Page: 383 / 943

Courtesy of VOLVO CARS CORPORATION

Remove:



the front seat as described in, see

FRONT SEAT



the tunnel compartment. See:

FLOOR CONSOLE



the front sill trim panel. See:

SILL EDGE

Fold the front floor carpet to one side.

Remove the rear air vent.

Pull / pry off the duct at the center console. Detach the duct at the upper mounting.

Press down the upper section of the duct in front of the cross member.

Pull the duct forwards. Detach the duct from the cross member.

INSTALLING CENTER AIR DUCT TO FLOOR REAR PASSENGER COMPARTMENT

Install:



the duct in the cross member and the front section of the duct in the upper mounting



the rear air vent



the floor carpet



the front sill trim panel, see:

SILL EDGE



the center console. See:

INSTALLING CENTER CONSOLE



the front seat as described in, see

FRONT SEAT

AIR DUCT FLOOR FRONT TO PASSENGER COMPARTMENT REAR, REPLACING

REMOVING FRONT AIR DUCT TO FLOOR REAR PASSENGER COMPARTMENT

2012 Volvo C30 T-5

HVAC Climate Units - Removal, Replacement And Installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands