Volvo 2008 C30 Service And Repair Manual Download

Page: 108 / 943

Fig. 11: Securing New Cover

Courtesy of VOLVO CARS CORPORATION



Pull the tabs down slightly and check that the edges of the cover surround the pedal edges. Pull the cover
to ensure that it is secure.



Repeat steps 8-10 for the remaining pedal.

APPLIES TO CARS WITH AUTOMATIC TRANSMISSIONS

Fig. 12: Removing Protective Film

Courtesy of VOLVO CARS CORPORATION



Take the two spacer washers from the kit. Remove the protective film from the covers. Ensure that the
surfaces of the pedals are clean.

2012 Volvo C30 T-5

BRAKES Hydraulic-Vacuum-Hydraulic Brakes - Installation Instructions, Accessories

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands