Volvo 2008 C30 Service And Repair Manual Download

Page: 49 / 943

Fig. 18: Identifying Seam-Weld Area On Collar

Courtesy of VOLVO CARS CORPORATION

Seam-weld the collar into place using 8 welding seams each measuring 30 mm. See the illustration.

Install:



the wheel arch. See:

FRONT WHEEL BEARING



the front side panel. See:

BRACKET FRONT PIECE

Carry out finishing work. See:

FINISHING WORK (COMMON TO BOTH METHODS)

SIDE MEMBER, UPPER, REPLACING

REMOVING THE OUTER SECTION OF THE UPPER SIDE MEMBER

2012 Volvo C30 T-5

ACCESSORIES AND BODY, CAB Body Frame - Removal, replacement and installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands