Volvo 2008 C30 Service And Repair Manual Download

Page: 71 / 943

replaced.

Remove the following items:



Rear fender. See

FENDER



B-pillar. See

B-POST



A-pillar. See

A-PILLAR

Alternative cutting points.

Fig. 53: Identifying Body Sill Weld Points (1 of 2)

Courtesy of VOLVO CARS CORPORATION

Fig. 54: Identifying Body Sill Weld Points (2 of 2)

Courtesy of VOLVO CARS CORPORATION

Install the following items:



B-pillar. See

B-POST



A-pillar. See

A-PILLAR

2012 Volvo C30 T-5

ACCESSORIES AND BODY, CAB Body Frame - Removal, replacement and installation

Summary of Contents for 2008 C30
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands

Volvo 2008 C30, Service And Repair Manual

Search results

Summary of Contents for 2008 C30

Reviews:

Related manuals for 2008 C30

Brands by name

Popular brands