manualshive.com logo in svg

Viavi CellAdvisor 5G, User Manual

The Viavi CellAdvisor 5G is an advanced network testing tool designed to ensure seamless connectivity in the era of 5G technology. For quick and easy access to all its features, refer to our comprehensive user manual available for free download on our website.

Share
Download
background image

CellAdvisor 5G User's Guide 

335 

 

 

 

 

Setting measure setup 

1

      

Tap the 

Setup

 (

)icon on the side bar of each measurement mode. 

2

      

To set the CPRI line bit rate, tap 

Link Rate

 under 

Port Configuration

 and select the CPRI link rate option from 

614.4 Mbps

, 

1228.8 Mbps

, 

2457.6 Mbps

, 

3072.0 Mbps

, 

4915.2 Mbps

, 

6144.0 Mbps

, 

9830.4

 

Mbps

 or 

10137.6 Mbps

. 

 

NOTE: 

It is important that you set the link rate correctly to avoid any misleading LOS and LOF alarms displayed on the 
screen. 

3

      

To turn on or off the through mode, tap 

On

 or 

Off

 in 

Thru

 line. 

4

      

To set the Tx Clock, tap 

Recovered

 (default) in 

Clock

 box. 

Summary of Contents for CellAdvisor 5G








































































































































































































































































































































































Reviews:

No comments

Related manuals for CellAdvisor 5G

Keithley 486 Quick Reference Manual preview
486
Brand: Keithley Pages: 48
Accu-Chek Inform II Training Manual preview
Inform II
Brand: Accu-Chek Pages: 12
Callaway 350TL Manual preview
350TL
Brand: Callaway Pages: 13
VEE GEE BX-3 Operation Manual preview
BX-3
Brand: VEE GEE Pages: 2
Yamaha Clavinova CVP-601 Reference Manual preview
Clavinova CVP-601
Brand: Yamaha Pages: 98
Yamaha Electone CSY-1 Manual preview
Electone CSY-1
Brand: Yamaha Pages: 28
Omega DP41-W User Manual preview
DP41-W
Brand: Omega Pages: 170
Technoline EA 3000 Operating Manual preview
EA 3000
Brand: Technoline Pages: 1
LaserLiner 4K5 RA 800 Manual preview
4K5 RA 800
Brand: LaserLiner Pages: 52
Omega FMG3000 SERIES User Manual preview
FMG3000 SERIES
Brand: Omega Pages: 16
A&D AD-1611 Instruction Manual preview
AD-1611
Brand: A&D Pages: 10
OLYS Peak Flow Manual preview
Peak Flow
Brand: OLYS Pages: 2
Keithley 6487 Reference Manual preview
6487
Brand: Keithley Pages: 338
Hach LANGE 5130 Quick Start Manual preview
LANGE 5130
Brand: Hach Pages: 2
BERG UBN204 Standard Protocol Manual preview
UBN204
Brand: BERG Pages: 23
EXFO PMD Analyzer 5500B Specification preview
PMD Analyzer 5500B
Brand: EXFO Pages: 4
Endress+Hauser Prolevel FMC 662 Installation And Operating Instructions Manual preview
Prolevel FMC 662
Brand: Endress+Hauser Pages: 52
Hanna Instruments HI88703-02 Instruction Manual preview
HI88703-02
Brand: Hanna Instruments Pages: 32

Brands by name

Popular brands

Load more brands