Viavi CellAdvisor 5G Page 24 User Manual Download | Manualshive

Page: 24 / 359

background image

Getting Started

12

CellAdvisor 5G User's
Guide

A manual that is stored in the USB memory stick

Optional accessories

Item

Description

Soft carrying case
(G700050431)

Light weight cases allow you to store your test instrument when it is not being used. The size is
420 (H) x 270 (W) x 285 (D) mm. The CellAdvisor 5G soft carrying cases are designed to have a
main base unit and modules.

Horn Antenna
(G700050370)

It is a Ka-band pyramidal horn antenna that operates from 26.5 to 40 GHz. The antenna offers
20 dBi nominal gain and a typical half power beam width of 14 degrees on the E-plane and 16
degrees on the H-plane. The antenna suppports linear polarized waveforms. The input of this
antenna is a WR-28 waveguide with UG-599/U flange.

The Horn Antenna Kit consists of Horn Antenna and WR-28 Waveguide Adaptor.

Omni-directional
Antenna K(f), 26 GHz to
40 GHz (G700050340)

It is a full band, Ka band omnidirectional antenna that covers the frequency range of 26.5 and 40
GHz. This vertically polarized antenna offers 360 degrees azimuth coverage with a 3 dBi typical
gain and ±1 dB nominal gain flatness. The antenna features a half power beam width of 45
degrees in its vertical direction. The RF port of the antenna is equipped with WR-28 waveguide
with UG-599/U flange.

GPS SMA Mount
Antenna

It is GPS L1(1575.42 MHz) Passive Antenna with -5 dBi gain. It is easy to connect to the
CellAdvisor 5G GPS port because of SMA plug.

Exploring the CellAdvisor 5G

Top panel

The CellAdvisor 5G product has the following top view.

Top panel view with optical hardware options

No.

Description

«
...
22
23
24
25
26
...
»

Summary of Contents for CellAdvisor 5G








































































































































































































































































































































































Reviews:

No comments

Related manuals for CellAdvisor 5G

Brand: E Instruments Pages: 2

Brand: ICP DAS USA Pages: 71

HYDROTECHNIK MultiHandy 2025

Brand: ICS Pages: 8

Brand: ICT International Pages: 24

Brand: Valhalla Scientific Pages: 43

Brand: Veeder-Root Pages: 59

Brand: JENCO Pages: 13

Brand: THORLABS Pages: 21

Brand: MICRO-EPSILON Pages: 82

Brand: OmegaWatt Pages: 9

Engine Analyzer Series

Brand: ACCEL DFI Pages: 39

Brand: Omega Pages: 13

Brand: Kawai Pages: 166

TRIAXIAL ELF SK-8301

Brand: Kalse Pages: 2

MEMORY HiCORDER MR8870-20

Brand: Hioki Pages: 20

Brand: YOSensi Pages: 27

Brand: Scheppach Pages: 20

Prosonic S FMU90 PROFIBUS DP

Brand: Endress+Hauser Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands