Viavi CellAdvisor 5G Page 32 User Manual Download | Manualshive

Page: 32 / 359

background image

Getting Started

20

Items

Menu

Description

Trace

Tap to set the Trace related parameters. The Trace menu pops up on the right side.

Amp/Scale

Tap to set the Amp/Scale related parameters. The Amp/Scale menu pops up on the right
side.

BW/AVG

Tap to set the BW/AVG related parameters. The BW/AVG menu pops up on the right side.

Sweep

Tap to set the Sweep related parameters. The Sweep menu pops up on the right side.

Channel

Tap to set the Channel related parameters. The Channel menu pops up on the right side.

Frequency

Tap to set the Frequency related parameters. The Frequency menu pops up on the right
side.

Trigger

Tap to set the Trigger related parameters. The Trigger menu pops up on the right side.

Limit

Tap to set the Limit related parameters. The Limit menu pops up on the right side.

Marker

Tap to set the Marker related parameters. The Marker menu pops up on the right side.

Menus on the side bar

Items

Name

Description

Menu

Tap to view all menus for the selected measurement and mode. Note that the Menus vary based on
the selected measurement and mode.

Setup

Tap to view measure setup menus for the selected measurement and mode. Note that the measure
setup menus vary based on the selected measurement and mode.

Full menu

Tap to view full menus for the selected measurement and mode in one screen. You can set all the
parameters needed for a test at once.

More

Tap to view more hot keys available.

Help

Tap to view the CellAdvisor 5G Help.

Hot keys and icons on the side bar

Items

Name

Description

Hold

Tap to hold spectrum measurement.

«
...
30
31
32
33
34
...
»

Summary of Contents for CellAdvisor 5G








































































































































































































































































































































































Reviews:

No comments

Related manuals for CellAdvisor 5G

Brand: Callaway Pages: 11

Brand: Olympus Pages: 12

Monitoring System 500 II DC

Brand: Didactum Pages: 2

Brand: Victron energy Pages: 46

Brand: Omega Pages: 20

RLACS277RLACS29

Brand: Racelogic Pages: 10

Brand: A&D Pages: 2

Brand: Rinstrum Pages: 2

Brand: YATO Pages: 52

Brand: Heyl Pages: 2

Brand: Milkotester Pages: 44

MarMonix MSL-765

Brand: Farnell Pages: 15

Brand: Shimadzu Pages: 22

Solar Auxiliary Power Unit

Brand: J-TECH Pages: 6

Brand: Lumel Pages: 32

Brand: Oakton Pages: 26

Brand: Avtech Pages: 40

Brand: Young Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands