background image

PROFINET IO

vacon • 123

Local contacts: https://www.danfoss.com/en/contact-us/contacts-list/

8

8.4.6.4

Response header

The response header consists of 4 fields, each one is octet in size.

Table 87. Response header

0x20

Parameter text cannot be 
changed

Change request to unavailable parameter text.

0x21

Invalid request ID

If a parameter request does not have the request ID 
01h or 02h, this error code is returned.

0x22...0x64

Reserved (not used)

0x65

Invalid request reference

Unallowed value for request reference.

0x66

Invalid request ID

Unallowed value in request ID (neither Request Pa-
rameter nor Change Parameter).

0x67

Reserved (not used)

0x68

Invalid number of parame-
ters

Invalid number of parameters in request (0 or 
greater than 39).

0x69

Invalid attribute

Invalid attribute specified in request.

0x6A

Reserved (not used)

0x6B

Request is too short

Not enough parameter value data was transmitted 
in a Change request. Alternatively, the request did 
not contain a complete parameter address.

0x6C

Parameter not found.

Parameter was not found or error occurred while 
accessing it.

0x6D

Invalid change request.

Issue with request was found and request was not 
handled.

0x6E

General error

General error occurred.

0x6F...0xFF

Reserved (not used)

Octet 

number

Field name

Description

Allowed values

1

Request Reference

Unique number for each 
request/response pair.

Mirrored by the slave.

2

Response  ID

Defines the type of 
response. An error in the 
execution of a request is 
indicated by setting bit 7 in 
this field.

Uses 0x01 for successful request 
parameter operation.
Uses 0x02 for successful change 
parameter operation.
Uses 0x80 to indicate that an invalid 
request ID was received.
Uses 0x81 for unsuccessful request 
parameter operation.
Uses 0x82 for unsuccessful change 
parameter operation.
Other values are not used.

3

Axis Number

Not used, should be set to 1. Mirrored by the slave.

4

Requested number 

of parameters

The number of parameters 
affected by the request.

Number of parameters in the 
response. Mirrored from the request.

Table 86. PROFIdrive parameter access errors

Error number Meaning

When used

Summary of Contents for optea






























































































































































































































































Reviews: