Home
/
Tieline
/
Genie Distribution
/
User Manual

Tieline Genie Distribution, User Manual, Page: 138 / 426

Share

Page: 138 / 426

Tieline Genie Distribution User Manual Download Page 138

138

Genie Distribution WNET Manual v3

© Tieline Research Pty. Ltd. 2020

Configure Link Mode

It is possible to configure the Ethernet link speed (10/100/1000/Auto) and whether each available
interface operates in full-duplex or half-duplex modes.

1. Click the drop-down

Link Mode

arrow and select the preferred setting.

2. Click

Save

to store the new setting.

IPv4 Address Configuration

Click to select the

TCP/IP

tab in the

Network

panel to configure settings. The codec is capable of

automatic DHCP address assignment, or manually configured static IPv4 address configuration via
the

Configure IPv4

drop-down menu. To ignore IPv4 settings select

Off

.

DHCP IP addresses are automatically assigned and can change each time you connect to your
Internet Service Provider, or to your own local area network (LAN). By default the codec is
configured for DHCP-assigned IP addresses.

«
...
136
137
138
139
140
...
»

Summary of Contents for Genie Distribution











































































































































































































































































































































































































































Reviews:

No comments