S&C IntelliTEAM II Instruction Sheet Download Page 32 | Manualshive

Page: 32 / 78

background image

32 S&C Instruction Sheet 1043-550

Forward Action / Reverse Action

These columns display two pieces of information. One is the name of the step what will
be taken during execution of the Action Path. The other is a timestamp associated with
the start of that step. The list names that will be displayed are:

Action path done

Close for xfer

Contract

request

Contract

terminate

Block

recloser

Unblock

recloser

Block ground trip

Unblock ground trip

Alternate

settings

Normal

settings

Status

These columns display two pieces of information. One is the status of the associated step
in the action path. The status can be Idle, Running, Failed, or Success.

Team Problems

«
...
30
31
32
33
34
...
»

Summary of Contents for IntelliTEAM II















































































Reviews:

No comments

Related manuals for IntelliTEAM II

Brand: Canon Pages: 2

HomeTec Pro CFF3000

Brand: Abus Pages: 13

Brand: NAVITAS Pages: 7

Brand: Abus Pages: 2

Brand: Sanhua Pages: 3

Brand: Zodiac Pages: 12

Brand: National Instruments Pages: 34

Brand: Eaton Pages: 96

EP Series Pro-Bloc

Brand: Parker Pages: 11

Brand: Parker Pages: 22

Brand: Parker Pages: 2

Brand: Daruifuno Pages: 24

Brand: M-system Pages: 10

Brand: WAGNER Pages: 128

Brand: Hach Pages: 504

Brand: Leggett & Platt Pages: 20

Brand: Adaptec Pages: 2

Brand: Webasto Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands